Ethernet-DMX4 / Truss MkII With PoE Input

The Ethernet-DMX4/Truss MkII is an Ethernet node that serves four DMX512 outlets, conform to DMX512-A, that can be used as input or output. The Ethernet links on the front and the side are 10/100BaseTX connections on Neutrik RJ45 Ethercon connector. All configuration can be done over Ethernet through a build in Web site. This all comes in a solid metal enclosure, ideal for table top, wall mounted or truss mounted application.

Key Features

  • DMX routing, universe setting
  • Input and output enable / disable
  • DMX output frame rate setting
  • Supported protocols: DMX, DMX512-A, RDM, Art-Net™, sACN
  • Protocol selection per port
  • IP settings
  • Unit ID and labeling
  • Graphic diplay and jog for settings visualization
  • Ethernet activity indication on front panel
  • Up to 40 programmable profiles and routings
  • Up to 10 predefined profiles (splitters, mergers…)
  • Multi language Web interface

Connections

  • 2 x 10/100BaseTX Ethernet connections on Neutrik RJ45 Ethercon connector
  • 4 x Isolated DMX512-A in/outputs via RJ45 connectors, with termination (DMX512-A)
  • 1 x Neutrik Powercon inlet
  • 1 x M10 insert for truss clamp
  • 1 x Safety eye

Operation

  • Ethernet <-> DMX conversion
  • Ethernet and DMX Merger
  • Ethernet and DMX Backup
  • DMX splitter / booster
  • DMX trigger. Remote selection of the control source
  • Built-in DMX softpatch
  • Wysiwyg enabled. DMX inputs can be visualised in Wysiwyg
  • DMX snapshot. Capture 3 fixed lighting states per outlet
  • Modification of captured values from the Web interface
  • Auto-load capture on boot-up (ideal for expo)
DMX 4 x shielded & gold plated Neutrik 5 pin XLR (female)
Network 2 x 10/100Mbps Neutrik RJ45 Ethercon connectors (front and side)
Power 1 x Neutrik Powercon inlet
Clamp 1 x M10 insert, 1 x Safety Eye
Supported DMX Protocols: DMX512 (1986 & 1990), DMX512-A, RDM ANSI E1.20
DMX Port Direction Input or output (configurable)
DMX Port Isolation Optic and galvanic isolation per port
DMX Port Termination/Biasing Yes
DMX Timing Framerate: 10-40fps / Break: 176-352µs
Supported Ethernet Protocols: Art-Net™, sACN ANSI E1.31
Port speed 10/100BaseTx
Port sensing Auto-negotiation, MDI/MDIX
Monitoring software LumiNet Monitor V2 at no cost
Wysiwyg Enabled Yes (visualize inputs)
Graphic Display & Jog Settings informations (IP address, netmask, outlet settings…)
Ethernet Port Connection Link and activity
Power LED indication
Power Input 90-260 VAC, 47-63 Hz
Power Consumption Maximum 15 W
Fuse 1A 250V Slow Blow
Power over Ethernet (PoE) Support Optional
Operating temperature 0 to +60 °C
Storage temperature -10 to +70 °C
Humidity 5-95% non-condensing
Enclosure Bended metal
Dimensions (WxDxH) 235 x 134,2 x 82 mm, 9,3″ x 3,5″ x 3,2″
Weight 2,3 Kg
Packaging (WxDxH) 305 x 215 x 110 mm
Additional information Approvals: CE, EN 55103-1, EN 55103-2, EN 60950-1, RoHS Compliance

Order References: Ethernet-DMX4/Truss MkII: LU 01 00029

Ethernet-DMX4/Truss MkII with PoE module: LU 01 00029-POE

Optional PoE Module: LU 01 00046 (Complies only with units from serial Lum0290251)

Note: Luminex LCE operates a policy of continuous development. Luminex LCE reserves the right to make changes and improvements to any of the products described in this document above without prior notice. Specifications are subject to change without notice.